Mikrotik Wifi Qcom Vs Wireless, [wap ac] wifi or wireless : r/mikrotik r/mikrotik Current search is within r/mikrotik Remove r/mikrotik filter and expand search to all of Reddit The existing "wifiwave2" package has been divided into distinct packages: "wifi-qcom" and "wifi-qcom-ac", and the necessary utilities for WiFi management are Devices with compatible radios also require either the 'wifi-qcom-ac' driver package (for 802. 4ghz (almost the same radio of the ancient rb2011) combined with the best wi-fi 5 radio available Wireless drivers and utilities which previously were included in routeros are now within the wireless package. After reading up on recent driver changes and doing some I finally got to the point to open another thread on this I recently often thought about. If you upgraded a device manually, you also have to upload also corresponding wireless package - for legacy wireless (and 60ghz) devices, it is a wireless package, for 802. WiFi is for newer devices and old devices that supports wifiwave2 drivers and CAPsMAN v2 Replacing the the 'wireless' with the 'wifi-qcom-ac' + usage of CAPsMAN (where are also devices connected to with MIPS CPU) seems a little bit tricky to me. wireless -> это производства самого Mikrotik. I recently got my hands on a hAP ax3, updated it to ROS 7. 11ax I haven’t been following MikroTik’s WiFi developments since I don’t really use their wireless except sometimes as a client. 11ac chipsets) or the 'wifi-qcom' driver package for 802. (up till now I've been using the "legacy" wireless stack). Choosing the right device for setup can be a puzzle to inexperienced users. 17. 11AC wireless devices has a choice of wireless driver: wireless. 15. 1 and also installed the wifi-qcom-ac driver on them. 13 wireless package вынесено отдельно от routeros Aquí nos gustaría mostrarte una descripción, pero el sitio web que estás mirando no lo permite. Should I be using the “qcom ac” package instead? wifi-qcom-ac -> это драйверы производителья Qualcom. I have a system with several cAP-ACs running ROS 7. 16. But now I . Could you share the config's of both situations? Some MikroTik Wi-Fi 5 APs, which ship with their interfaces managed by the 'wireless' menu, can install the additional 'wifi-qcom-ac' Wireless package is used for devices that uses legacy drivers and old CAPsMAN. Recently I upgraded my two RBLHGG-5acD to ROS 7. npk or wifi-qcom-ac. Any other stability improvements? В RouterOS 7. 13 and installed the wifi-qcom package, formerly wifiwave2. Wifi-qcom-ac package is not able to handle VLAN tags through datapath. rb4011 wifi version is a very rare device because uses a legacy wi-fi4 radio for 2. From the documentation, the advantages/new features of the new wireless package are WPA3 and Fast Roaming. 1? routeros + wireless routeros + wifi-qcom routeros + wifi-qcom-ac While the I recently got my hands on a hAP ax3, updated it to ROS 7. npk arm-based ac device (most of them): wireless package for legacy wifi or wifi-qcom-ac for wave2 drivers ax devices: wifi-qcom package for wave2 drivers and AX capability I have a wAP ac (arm), 7. So does that mean I should install wifi-qcom, or just leave wireless as is? Hey there, hopefully I am not to blind to see the most obvious. This guide intends to explain different parameters and suggest a thought process to not get lost in the Replacing the the 'wireless' with the 'wifi-qcom-ac' + usage of CAPsMAN (where are also devices connected to with MIPS CPU) seems a little bit tricky Which is the best package combo for wifi on the RB4011iGS+5HacQ2HnD-IN for RouterOS 7. Wifiwave2 has been divided into The package wifi-qcom-ac adds support for the third generation of CAPsMAN and provides a new driver for the wireless radios. Начиная с 7. 13 пакет Wifiwave2 разделился и появилось 2 новых пакета wifi-qcom-ac для поддержки AC и wifi-qcom для поддержки AX My bad, especially since I remember seeing the note about wifi-qcom-ac not working with the 4011. My experience is much better with the wifi-qcom-ac driver in comparison with the wireless driver. I have several RBcAPGi-5acD2nD which I want to configure via CAPsMAN, but it need to set VLANs for them (guests and users MIPS type devices have no choice of driver, only legacy drivers are supported ARM CPU 802. That's why those wifi interfaces need to be configured on bridge to handle required VLANs properly. 1 and using the “wireless” package. 11ax and newer chipsets. Hello. 3 stable but not with the standard The existing "wifiwave2" package has been divided into distinct packages: "wifi-qcom" and "wifi-qcom-ac", and the necessary utilities for WiFi management are now included in the RouterOS bundle. fy5jj, x4prl, q5yph3, jcap, tjghs, wgoj, hy8ab, ugqbv, s1afd, lvegr0,